EPOXY
The question of EP-04 Epoxy Topcoat is about yellowing.
1.The epoxy reisn with yellowing property, so the yellowing result is different from before curing and after curing when the paint film explosed to UV light. Always, the yellowing result before curing is worse than after curing under the sun shine.
2.EP-04 Epoxy Topcoat is suitable to apply for interior structure, as to apply for exterior structure, the UP-04 PU Coating is recommendable.
2.EP-04 Epoxy Topcoat is suitable to apply for interior structure, as to apply for exterior structure, the UP-04 PU Coating is recommendable.
The automobile maintenance depot uses in the bipod crest elevation machine or the maintenance vehicle galvanized plate of, asked uses what kind of paint system?
Our suggestion is as follows:
1.Surface treatment：Clean the board by the steel brush, solvent and cleaner。
2.Primer：NO.1020 Epoxy Alloy Primer。
3.Topcoat：NO.1001 Epoxy Topcoat（EP-04）。
1.Surface treatment：Clean the board by the steel brush, solvent and cleaner。
2.Primer：NO.1020 Epoxy Alloy Primer。
3.Topcoat：NO.1001 Epoxy Topcoat（EP-04）。
In the roof the balcony corner and the cement floor want to do guard against leak processing, how should construct?
1.Surface treatment：The dirt of cement surface clean-up is clean, the iron pipe must grind and remove the rust.
2.Primer：NO.1073 Epoxy Clear Cement Primer (15μ ）。
3.Middle：NO.1080 Solventless Epoxy Elastomer Coating (200μ x 2 coats）。
4.Topcoat：NO.751 Elastic PU Coating (30μ ）。
2.Primer：NO.1073 Epoxy Clear Cement Primer (15μ ）。
3.Middle：NO.1080 Solventless Epoxy Elastomer Coating (200μ x 2 coats）。
4.Topcoat：NO.751 Elastic PU Coating (30μ ）。
What kind of coating should use in the stainless steel products?
1.Surface treatment：Clean grease by solvent.
2.Primer：NO.1020 Epoxy Alloy Primer （25μ ）
3.Topcoat：Interior : NO.1001 Epoxy Topcoat（40μ x 2 coats）；Exterior : UP-04 PU Coating（30μ x 2 coats)
2.Primer：NO.1020 Epoxy Alloy Primer （25μ ）
3.Topcoat：Interior : NO.1001 Epoxy Topcoat（40μ x 2 coats）；Exterior : UP-04 PU Coating（30μ x 2 coats)
What kind of coating should use in the lubricating oil tank internal?
Our suggestion is as follows:
EP-4556 High-solids Amine-cured Epoxy (100μ x 3 coats) or Solvent Free Amine-cured Epoxy (150μ x 2 coats)
EP-4556 High-solids Amine-cured Epoxy (100μ x 3 coats) or Solvent Free Amine-cured Epoxy (150μ x 2 coats)
What is the method of FRP application for the acid resistance in mechanical equipment?
Our recommendation is as follows ：
1.Surface treatment ：Sand blast to above SIS Sa 2 1/2.
2.NO.1615SP Vinyl Ester Sealer/Primer （For steel）100μ
3.NO.1606 Vinyl Ester Fiber Glass Multilayer Lining（EM-450）
4.NO.1606 Vinyl Ester Fiber Glass Multilayer Lining（EM-300）
5.NO.1606 Vinyl Ester Fiber Glass Multilayer Lining（EM-30）
6.NO.1607 Vinyl Ester Finish 100μ
1.Surface treatment ：Sand blast to above SIS Sa 2 1/2.
2.NO.1615SP Vinyl Ester Sealer/Primer （For steel）100μ
3.NO.1606 Vinyl Ester Fiber Glass Multilayer Lining（EM-450）
4.NO.1606 Vinyl Ester Fiber Glass Multilayer Lining（EM-300）
5.NO.1606 Vinyl Ester Fiber Glass Multilayer Lining（EM-30）
6.NO.1607 Vinyl Ester Finish 100μ
How to use the Epoxy Putty？
The hardener (light red) pour into the base (white), and stir thoroughly still the red disappearance, then the mixture can be used to apply approximately 30 minutes (25℃) after mixing.
The pump motor soaks for a long time in the water, and need the black color paint that is able to guard against rust, asked what kind of product can be used?
Either uses No.1061H(EP-999H) High Solids Epoxy Coating to apply two coats, and the paint film must reach 250μ or EP-06 Epoxy-Tar, HB.
The EPOXY-TAR, HB belongs what kind of coating, and when used in the concrete whether has the function of waterproof?
The EPOXY-TAR is our product of No.1078 EPOXY-TAR, HB that might use in the concrete moreover has anti-corrosive and waterproof function. The recommended painting system is as follows:
1.Primer ： NO.1073 EPOXY CLEAR CEMENT PRIMER.
2.Topcoat ： NO.1078 EPOXY-TAR, HB (250μ×2 coats), and the overcoating interval is one day.
1.Primer ： NO.1073 EPOXY CLEAR CEMENT PRIMER.
2.Topcoat ： NO.1078 EPOXY-TAR, HB (250μ×2 coats), and the overcoating interval is one day.
How many square meters can apply with one gallon of the epoxy coating light colored series?
According to the thickness of dry film 40μ of the EP-04 Epoxy Topcoat calculation, 1 gallon might paint 25～27M² approximately
What kind of paint system should use for the avgas tank inside?
Our commendation is as follows:
Use EP-4556 High-Solids Amine-Cured Epoxy to paint 3 coats, each coat get 100μ of paint film
Use EP-4556 High-Solids Amine-Cured Epoxy to paint 3 coats, each coat get 100μ of paint film
What kind of paint system should use for the avgas tank inside (load pressure oil) to resist the acid and alkali?
1.Sand to blast SIS Sa 2 1/2.
2.EP-4556 High-Solids Amine-Cured Epoxy (100μ x 3 coats) or EP-4556F Solvent Free Amine-cured Epoxy (150μ x 2 coats) .
2.EP-4556 High-Solids Amine-Cured Epoxy (100μ x 3 coats) or EP-4556F Solvent Free Amine-cured Epoxy (150μ x 2 coats) .
What kind of paint system should use to resist rust for the freezer?
(A）Internal ：
NO.1027 Epoxy Zinc Rich Primer（EP-03AA）50μ .
NO.1009 Epoxy Red Oxide Primer（EP-02）45μ .
NO.1001Epoxy Topcoat（EP-04 ), 40μ x 2 coats .
(B）External：
NO.1027 Epoxy Zinc Rich Primer（EP-03AA）50μ .
NO.1050 Epoxy M.I.O. Primer（EP-20）75μ .
UP-04 PU Coating, 30μ x 2 coats.
NO.1027 Epoxy Zinc Rich Primer（EP-03AA）50μ .
NO.1009 Epoxy Red Oxide Primer（EP-02）45μ .
NO.1001Epoxy Topcoat（EP-04 ), 40μ x 2 coats .
(B）External：
NO.1027 Epoxy Zinc Rich Primer（EP-03AA）50μ .
NO.1050 Epoxy M.I.O. Primer（EP-20）75μ .
UP-04 PU Coating, 30μ x 2 coats.
What kind of paint system should use for the internal of diesel tank?
Our recommendation is as follows:
Use EP-4556F Solvent Free Amine-cured Epoxy to get 300μ of paint film by 2 coats or EP-4556 High-Solids Amine-Cured Epoxy 100μ x 3 coats, total 300μ.
Use EP-4556F Solvent Free Amine-cured Epoxy to get 300μ of paint film by 2 coats or EP-4556 High-Solids Amine-Cured Epoxy 100μ x 3 coats, total 300μ.
The cement floor happened the flaking phenomenon when had applied the EP-04 Epoxy Topcoat.
There are the causes as follows:
1.Because of the ground moisture rise, therefore the suggestion is to test by the adhesive tape and sure no moisture rise before coating. If still has same result, we suggested you to use the water-based epoxy series.
2.The surface of cement must use the grinder suitable abrasion to have rough surface for easy adhesion.
1.Because of the ground moisture rise, therefore the suggestion is to test by the adhesive tape and sure no moisture rise before coating. If still has same result, we suggested you to use the water-based epoxy series.
2.The surface of cement must use the grinder suitable abrasion to have rough surface for easy adhesion.